Skip to main content

Circular Saw Blade Buying Guide 2-Standard Circular Saw Blades

Standard circular saw blades are those you typically use to cut wood or wood composites. The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster but those with more teeth create a finer finish. Gullets between the teeth remove chips from the work pieces. Expansion slots cut into the rim help prevent the blade from warping as it expands and contracts during use. They reduce vibration, creating a straighter cut.

Rip-cut blades, those for cutting with the wood grain (along the length of a board), have fewer teeth (16 to 40). The teeth are designed to cut aggressively and deep gullets provide good chip removal. Crosscut blades, those for cutting across the wood grain (across the face of a board), have between 40 and 80 teeth designed for clean cuts. Smaller gullets separate the teeth. Combination blades can make rip cuts and crosscuts. They have multiple groupings of teeth separated by deep gullets. Each group has one tooth for ripping and four for crosscutting.

You may also see blades with other designations:

  • Framing blades have 24 teeth and are effective for work — such as rough carpentry — where speed is more important than a clean cut.
  • Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering.
  • Thin-kerf blades have a narrow profile for faster, easier cutting and less material waste.
  • Hollow-ground blades have a body that's thinner than the teeth — a design intended to help keep the blade from becoming pinched in the work piece.

Good to Know
Some standard circular saw blades can cut materials other than wood, such as plastic or aluminum.

Good to Know
Look for circular saw blade features such as anti-kickback designs and friction-reducing coatings.

See more at:http://www.sunwit-diamondsawblade.com/

Comments

Popular posts from this blog

How to make pig feed pellets

3 steps creating your own pig feed 1. after you area unit attending to build pig feed pellets on your own, the primary step is to form certain the wetness of your raw materials is concerning 10-12%. The wetter or appliance material can have an effect on the ultimate quality of finished pellets. you'll be able to use a drier, so you'll be able to get the perfect wetness quickly. otherwise you will dry it naturally within the sun. 2. the second step you've got to try to to is crushing your materials before you begin creating your own pig feed pellet pellets, if your raw materials size is just too abundant massive, it is not really easy to be ironed into pellets. after you crush it to fine powders, the finest, the better, the pelletizing rate and final pellets quality are going to be higher. 3. feeding your raw materials into the pig feed pellet mill machine through the feeder. they will be compressed to columnlike holes on the die and discharged from the machi...

usa selecting the right band saw blade

How to Choose the Right Bandsaw Blade NOTE: Choosing the right bandsaw blade depends on many factors; including type of ... Step 1 - Choose a Product: What Type of Bandsaw do you Have? Selecting the Right Band Saw Blade Contact Us (800) 981 9663. Your Orders ... Selecting the Right Band Saw Blade. To get the best, ... Constant - All teeth on the blade have uniform spacing, gullet depth, rake angle throughout the full length. Usually ... Constant Pitch Selection... How to Choose the Right Band Saw Blade - Border States 25 May 2016 ... There are many factors to consider when deciding which band saw blade is right for your project. Choosing the wrong blade can cause... Choosing the Right Bandsaw Blade - Woodcraft 27 Feb 2017 ... Choosing the Right Bandsaw Blade. Choosing the proper bandsaw blade for your saw, or application, is as simple as answering a few basic... 10 Essential Tips for Choosing a Band Saw Blade - Canadian ... It's not difficult to choose the right blade for your...

Circular Saw Blade Buying Guide 1

Different types of circular saw blades are designed to cut different materials and work with different power saws. Make sure the blade you choose is suitable for the material you need to cut. You also need to make sure it fits your saw. There are several specifications you should check. Look at the blade diameter and type and compare these specifications with the capability of your saw. Acceptable sizes vary by saw model, but in general: Handheld circular saws accept smaller blades, those 4-1/2 inches to 7-1/4 inches in diameter. These are typically carbide-tipped . Tile saws use 7-inch or 10-inch diamond blades. Table saws and compound miter saws use blades 10 inches or 12 inches in diameter. Like those for handheld saws, the blades are usually carbide-tipped . Metal-cutting chop saws , also called abrasive saws or cutoff saws , take 14-inch silicon carbide or aluminum oxide abrasive blades. Check the size of the arbor hole (the hole in the cen...