Skip to main content

Why use diamond tipped bladed over normal blades?

the uses for diamond tipped blades do go beyond masonary- you can get diamond impregnated blades for cutting metal, also. Most diamond blades are used for cutting concrete, brick, stone, block, tile, asphalt, fibercement siding, and terrazzo. There are many different styles of blades, and each has a semi-specific material to cut. Some blades require that they have a constant stream of water sprayed on them to cool the blades. Some are only for green, uncured concrete and asphalt. Some are for tile or porcelean only. The difference isn't the diamonds, but the material the blade is made out of. The medium that holds the diamonds in place in the blade is designed to wear at a different rate-depending on the material. Using a blade designed to cut block or cured concrete to cut asphalt will result in the blade galling up-basically you'll wear the exposed diamonds off, but the asphalt isn't abrasive enough to wear the medium down enough to get to the next layer of diamonds, and the blade will stop cutting until you run it in a block or cured concrete. Using a blade that's designed to be used with water without water will result in the blade warping, and it will be impossible to cut a straight line. Also, different blades are designed for each specific tool they are used on. That means that they are designed to run at different RPM's. Never use a blade in a tool(such as a gas powered cut off saw) that spins faster than the recommended safe rpm for the blade-it will basically fly apart.

The other answers gave you the difference between blades. I'll go a step further. Different blades have specific intended purposes. You should use the type of blade to fit your purpose. I cut mainly wood and have about a dozen different blades, some fine cut, some rip, etc. I use a torch and abrasive disk blade for cutting metal. I have never cut tile so I don't have any diamond blades. I discovered many years ago that a sharp tool works far better than dull ones.

Diamond blades are used to cut masonry. Period. Use a carbide tipped blade to cut through wood (diamond will just burn it), and use a metal cutting blade for metal. There are different types of metal blades for ferrous (steel) and non-ferrous metals. There is a correct tool for each job, and this is a perfect example. Good luck.

Source(s): http://www.chinadiamonddisc.com/

Labels:

Comments

Post a Comment

Popular posts from this blog

How to make pig feed pellets

3 steps creating your own pig feed 1. after you area unit attending to build pig feed pellets on your own, the primary step is to form certain the wetness of your raw materials is concerning 10-12%. The wetter or appliance material can have an effect on the ultimate quality of finished pellets. you'll be able to use a drier, so you'll be able to get the perfect wetness quickly. otherwise you will dry it naturally within the sun. 2. the second step you've got to try to to is crushing your materials before you begin creating your own pig feed pellet pellets, if your raw materials size is just too abundant massive, it is not really easy to be ironed into pellets. after you crush it to fine powders, the finest, the better, the pelletizing rate and final pellets quality are going to be higher. 3. feeding your raw materials into the pig feed pellet mill machine through the feeder. they will be compressed to columnlike holes on the die and discharged from the machi...
Post a Comment
Read more

usa selecting the right band saw blade

How to Choose the Right Bandsaw Blade NOTE: Choosing the right bandsaw blade depends on many factors; including type of ... Step 1 - Choose a Product: What Type of Bandsaw do you Have? Selecting the Right Band Saw Blade Contact Us (800) 981 9663. Your Orders ... Selecting the Right Band Saw Blade. To get the best, ... Constant - All teeth on the blade have uniform spacing, gullet depth, rake angle throughout the full length. Usually ... Constant Pitch Selection... How to Choose the Right Band Saw Blade - Border States 25 May 2016 ... There are many factors to consider when deciding which band saw blade is right for your project. Choosing the wrong blade can cause... Choosing the Right Bandsaw Blade - Woodcraft 27 Feb 2017 ... Choosing the Right Bandsaw Blade. Choosing the proper bandsaw blade for your saw, or application, is as simple as answering a few basic... 10 Essential Tips for Choosing a Band Saw Blade - Canadian ... It's not difficult to choose the right blade for your...
Post a Comment
Read more

Circular Saw Blade Buying Guide 1

Different types of circular saw blades are designed to cut different materials and work with different power saws. Make sure the blade you choose is suitable for the material you need to cut. You also need to make sure it fits your saw. There are several specifications you should check. Look at the blade diameter and type and compare these specifications with the capability of your saw. Acceptable sizes vary by saw model, but in general: Handheld circular saws accept smaller blades, those 4-1/2 inches to 7-1/4 inches in diameter. These are typically carbide-tipped . Tile saws use 7-inch or 10-inch diamond blades. Table saws and compound miter saws use blades 10 inches or 12 inches in diameter. Like those for handheld saws, the blades are usually carbide-tipped . Metal-cutting chop saws , also called abrasive saws or cutoff saws , take 14-inch silicon carbide or aluminum oxide abrasive blades. Check the size of the arbor hole (the hole in the cen...
Post a Comment
Read more